The
instances included in NODAS_HP library are listed below:
anchor
beam_0010
beam_0011
beam_0100
beam_0101
beam_0110
beam_0111
beam_1000
beam_1001
beam_1010
beam_1011
beam_1100
beam_1101
beam_1110
beam_1111
comb_1111_1
comb_1111_2
comb_diff_1111_1
comb_diff_1111_2
frame_1000
layout_origin
plate_1000
ANCHOR
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l and w |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns;
- l denotes a direction perpendicular to a side where the anchor
is connected to another element.
- w denotes a direction parallel to a side where the anchor is
connected to another element.
|
BEAM_0010
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_0011
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_0100
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_0101
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_0110
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_0111
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_1000
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_1001
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_1010
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_1011
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_1100
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_1101
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_1110
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
BEAM_1111
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
l, w, angle |
DESIGN TIPS |
- values for l and w end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
|
Comb_1111_1
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
finger_width, finger_length,
angle, overlap, gap, fingers,
truss_width_a, truss_width_b,
wing_length_a, wing_length_b |
DESIGN TIPS |
- All properties except "angle" and "finger"
are required to end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
- The rotor (right side) has a number of fingers equal to the
property value of "fingers", while the stator (left
side) has 1 more finger.
|
Comb_1111_2
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
finger_width, finger_length,
angle, overlap, gap, fingers,
truss_width_a, truss_width_b,
wing_length_a, wing_length_b |
DESIGN TIPS |
- All properties except "angle" and "finger"
are required to end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
- The rotor (right side) has a number of fingers equal to the
property value of "fingers", while the stator (left
side) has 1 more finger.
|
Comb_diff_1111_1
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
finger_width, finger_length,
angle, overlap, gap, fingers,
truss_width_a, truss_width_b,
wing_length_a, wing_length_b |
DESIGN TIPS |
- All properties except "angle" and "finger"
are required to end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
- The rotor (right side) has a number of fingers equal to the
property value of "fingers", while the stator (left
side) has 1 more finger.
|
Comb_diff_1111_2
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
finger_width, finger_length,
angle, overlap, gap, fingers,
truss_width_a, truss_width_b,
wing_length_a, wing_length_b |
DESIGN TIPS |
- All properties except "angle" and "finger"
are required to end with the letter "u" denoting
microns,
- angle can be either "0" - terminals of type
"m" located on the left side of the symbol or
"90"- terminals of type "m" located on the
bottom of the symbol.
- The rotor (right side) has a number of fingers equal to the
property value of "fingers", while the stator (left
side) has 1 more finger.
|
frame_1000
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
none |
DESIGN TIPS |
|
LAYOUT_ORIGIN
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
|
DESIGN TIPS |
defines (0,0) layout co-ordinates and technology
library for layout generation therefore it has to be taken from
NODAS_poly library., |
PLATE_1000
SYMBOL |
|
PROPERTY
WINDOW
|
|
REQUIRED
PROPERTIES |
unitl, unitw, joint_offset,
percentage_holes
angle, unitnum_x, unitnum_y |
DESIGN TIPS |
- the length of the plate size is determined by taking the value
of unitl and multiplying it by unitnum_x.
the width of the plate size is determined by taking the value of
widthl and multiplying it by unitnum_y.
- The area of holes in each unit is defined by the property
percentage_holes(i.e. a plate with 50% of holes area holds the
percentage_holes property value of 0.5)
|
|